Directions
Reviver swipes contain a proprietary blend of organic odor neutralizers and hypo-allergenic fragrance New (2) from $6.99& FREE Shipping Give the gift of Amazon. 4170 Douglas Blvd, Suite 200, Granite Bay, CA 95746 [email protected] © 2020 ReviverMx, Inc., All Rights Reserved – v2.06.00. Revive definition, to activate, set in motion, or take up again; renew: to revive old feuds.
Instrucciones en EspañolMinwax® Hardwood Floor Reviver is designed to work on polyurethane-finished hardwood floors. It is not recommended for use on laminates, unfinished, newly finished, waxed or oiled floors, or for floors coated with finishes other than polyurethane. If you are unsure of what type of floor you have, consult a flooring professional before using Reviver.
Reviver is not designed for use on floors that are in very poor condition. Badly damaged floors or floors that have large areas where the finish is worn away will require a complete refinishing.
Prepare the Floor:
- Sweep or vacuum the floor to remove all loose dirt.
- Wash the floor with a mild, oil-free cleaner such as Minwax® Hardwood Floor Cleaner. Allow to dry completely.
- Test Reviver on an inconspicuous area of the floor to ensure adhesion and compatibility. Wax and ingredients in some floor polishes may prevent Reviver from adhering to the floor. Consult a flooring professional if wax or polish had been applied to the floor.
Apply the Coating:
- Rock the bottle several times before opening the cap. Do not shake.
- Squirt Reviver in an 'S' pattern directly onto a 3'x3' area of the floor.
- Use water to dampen a new painter's pad attached to a long pole. Use the damp pad to spread Reviver across the flooring area. Do not spread too thin! Work in the direction of the wood's grain using a back-and-forth motion. Smooth Reviver with the grain.
- Keep working in small sections until the entire floor is coated.
- For best results, apply an even coat. Keep airborne dust to a minimum while the floor is wet.
YOU’RE DONE!
Let the finish dry at least two hours before walking lightly on the floor. Do not walk on the floor if it is wet or tacky. Avoid heavy traffic and do not replace furniture or rugs for 24 hours after application. When replacing furniture, do not slide.
CLEANUP: Application tools can be easily cleaned with soap and warm water.
Reviver Shark Tank
Reviver can be reapplied as needed (usually about every 6 months) to keep your floors looking beautiful. Reviver leaves a permanent protective coating on your floor, which will help renew the floor's beauty and shine.
Notes: Reviver is a permanent finish that can only be removed by sanding. It is not strippable. Do not use on laminate floors. For best results, do not apply too thin. Applying too thinly may cause streaking. Do not apply with a sponge mop.
CAUTIONS: Contains Butoxypropanol. 1-Methyl-2-Pyrrolidinone. CONTAINS MATERIAL THAT MAY CAUSE ADVERSE REPRODUCTIVE EFFECTS AND MAY ADVERSELY AFFECT THE DEVELOPING FETUS BASED ON ANIMAL DATA.
Use only with adequate ventilation. To avoid overexposure, open windows and doors or use other means to ensure fresh air entry during application and drying. If you experience eye watering, headaches, or dizziness, increase fresh air, or wear respiratory protection (NIOSH approved) or leave the area. Avoid contact with eyes and skin. Wash hands after using. Keep container closed when not in use. Do not transfer contents to other containers for storage.
FIRST AID: In case of eye contact, flush thoroughly with large amounts of water. Get medical attentional if irritation persists. If swallowed, call Poison Control Center, hospital emergency room, or physician immediately.
WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
Reviver
DO NOT TAKE INTERNALLY. KEEP OUT OF THE REACH OF CHILDREN.